Costumes and Cosplay

How to Distress and Age a Steampunk Costume

Distress and age a steampunk costume with sanding, tea staining on natural fibers, washes for metal, and patina effects, testing each method first.

On this page
  1. Distress where real wear happens
  2. Sand, grate, and fray
  3. Stain with tea or coffee
  4. Add grime
  5. Age metal and props
  6. Age leather
  7. Test first, then build up gradually
  8. Misconceptions
  9. Safety

Distressing a steampunk costume makes it look used rather than new. Put the wear where real wear happens, build it up slowly, and test every method on scrap first. Overdone wear looks fake from more than a few feet away.

Distress where real wear happens

Real wear concentrates at hems, cuffs, collars, elbows, knees, pocket edges, the seat, and seams. Start with those areas. Wear should not be even across the whole costume.

Sand, grate, and fray

  • Abrade with 80 to 150 grit sandpaper, a cheese grater, a wire brush, pumice, or a rasp.
  • Fray raw edges by pulling threads, or by washing the garment on hot.

Stain with tea or coffee

Brew the tea or coffee strong. Soak the fabric for 15 minutes to several hours, then rinse. The color dries lighter than it looks when wet.

  • Tea and coffee stain natural fibers well, such as cotton, linen, silk, and wool.
  • They barely affect polyester, so check the fiber content first.
  • Tea and coffee stains are not fully permanent. They fade with washing, and how fast varies.
  • For a permanent tone, use a fabric dye such as RIT, or Dylon or Procion for cellulose fibers.

Add grime

Use diluted acrylic paint, fabric spray paint, an airbrush, fuller’s earth, or brown and black eyeshadow or pastel powder. Build the grime in layers, and keep it lightest on clean areas.

Age metal and props

  • Washes: apply a black or brown wash into the crevices, then wipe most of it back off.
  • Edges: dry-brush silver or gold along the raised edges.
  • Rust: layer burnt umber, burnt sienna, and orange, stippled on with a sponge.
  • Verdigris: brush teal or turquoise paint into the recesses of copper or brass finishes.

Real copper and brass patina can be made with chemicals, such as ammonia fumes or a vinegar-and-salt solution. These are hazardous. Use gloves and ventilation, and test on scrap first.

Age leather

Sand the edges and high points of the leather. Work antique paste into the creases to darken them. The leather then looks handled rather than stained.

Test first, then build up gradually

Test every method on scrap fabric or on a hidden spot. Build the effect up in small steps. Judge the result from 2 to 3 m (6 to 10 ft) away, since that is how other people will see it.

Misconceptions

  • More distressing doesn’t look better. Overdone wear looks fake.
  • Tea doesn’t stain synthetics.
  • Wear isn’t even all over. It concentrates at friction points.
  • Distressing can’t be undone. Start with cheap or thrifted pieces.

Safety

  • Never mix bleach with ammonia or vinegar. The mix creates toxic gas.
  • Use gloves and ventilation with bleach, dyes, and patina chemicals.
  • Wear a dust mask when sanding fabric and paint.

For the leather pieces you may be aging, see DIY steampunk leather bracers and wrist cuffs. For aging metal props such as a watch, see the pocket watch prop guide. The full build order is in the steampunk costume tutorial.

The complete guide to costumes and cosplay

Steampunk Costume Tutorial: Build a Cosplay Step by Step
Read the guide

Keep exploring

Guides from other topics

All topics →