Costumes and Cosplay

How to Make a Steampunk Mechanical Arm

Build a steampunk mechanical arm from EVA foam plates, telescoping PVC pistons, and tubing, with advice on patterning, joints, bonding, and painting.

On this page
  1. Choose an arm style
  2. Pattern the arm
  3. Cut the plates
  4. Build the segments
  5. Add fingers
  6. Add pistons and hoses
  7. Attach it to your body
  8. Bond the pieces
  9. Finish the arm
  10. Add lights (optional)
  11. Misconceptions
  12. Safety

A steampunk mechanical arm is mostly a matter of foam plates laid over a patterned shape, with a few moving-looking details added on top. The look comes from overlapping plates and finish, not from working parts.

Choose an arm style

There are three common approaches:

  • Armor over your real arm. This is the most common method.
  • A fake extra arm. The prop arm is separate from your real arm.
  • A hidden-arm illusion. Your real arm is tucked inside the costume, so the prop arm appears to be the only arm.

Pattern the arm

Wrap your arm in plastic wrap, then in duct tape. Draw the panel lines on the tape, cut the tape off, and flatten it onto foam. The flattened pieces become your templates.

Cut the plates

Use EVA foam at 5 to 6 mm for the main plates, and 2 mm for trim and rivet strips. Worbla is a sturdier alternative. It becomes workable at about 90°C (194°F), so use a heat gun with care and test on scrap first.

Build the segments

A full arm usually has these segments:

  • Shoulder cap
  • Upper arm
  • Elbow cop (the elbow cap)
  • Forearm vambrace
  • Gauntlet or glove

At the elbow, leave a gap or overlap the plates so the arm can bend.

Add fingers

You can glue plates to a glove, or run “tendon” cables made from fishing line or bike cable to rings. Either approach gives the hand a mechanical look without needing full articulation.

Add pistons and hoses

Telescoping PVC or brass tubing runs alongside the forearm. Fix one end and let the other slide. Pistons don’t need to move to look convincing, so a fixed piston is fine.

Hoses can be vinyl or corrugated tubing about 6 to 10 mm (1/4 to 3/8 in) across.

Attach it to your body

Attach the arm with elastic, Velcro, buckle straps, or a shoulder harness across the chest. The shoulder armor and harness guide covers harness construction. Keep heavy parts close to the shoulder, and remember that comfortable weight varies by person.

Bond the pieces

Use contact cement for foam seams. Hot glue is fine for small decorative parts, but on its own it won’t hold flexing foam seams.

Finish the arm

  1. Heat-seal the foam with a heat gun.
  2. Apply 3 to 4 coats of Plasti Dip.
  3. Paint a black or brown base.
  4. Add a brass or copper metallic finish.
  5. Apply a black wash.
  6. Dry-brush silver along the edges.

Painted and weathered foam reads as metal, so the arm does not need real metal parts.

Add lights (optional)

Use 3 mm or 5 mm LEDs powered by a CR2032 coin cell, or by an AA or USB battery pack hidden in the harness. Check each LED’s rated voltage and current, and add a resistor if the LED’s datasheet calls for one. Secure the battery and insulate the wiring.

Misconceptions

  • The arm doesn’t need real metal. Foam reads as metal once it is painted and weathered.
  • It doesn’t need full articulation. Overlapping plates sell the effect.
  • Hot glue won’t hold flexing foam seams. Use contact cement.
  • Pistons don’t need to move to look convincing.

Safety

  • Wear a dust mask when sanding foam or Worbla, or when using a rotary tool on them.
  • Leave the wrist and elbow joints free to move, and test your reach before you wear the arm out.

For the wider costume, see the steampunk costume tutorial. For another harness-mounted prop, see the steampunk jetpack.

The complete guide to costumes and cosplay

Steampunk Costume Tutorial: Build a Cosplay Step by Step
Read the guide

Keep exploring

Guides from other topics

All topics →