DIY Crafts

How to make homemade props?

Make homemade props from EVA foam, cardboard, Worbla, resin or 3D prints. Learn the materials, priming and paint steps, and the safety rules for prop weapons.

On this page
  1. Choose a material
  2. EVA foam basics
  3. Worbla and thermoplastics
  4. Shape with patterns
  5. 3D prints and hard shells
  6. Repeat details with silicone molds
  7. Paint and finish
  8. Conventions and realistic props
  9. Safety

To make a homemade prop, pick a material that suits the job, such as EVA foam, cardboard, PVC pipe, Worbla, resin, polymer clay or 3D prints. Then shape and bond the pieces, prime them, paint them and seal them. Foam and cardboard are common starting points because they are light and simple to cut.

Choose a material

Material Good for Watch for
EVA foam Armour, shaped pieces, cosplay parts Prime before painting; heat-seal the surface
Cardboard Light, quick shapes Warps; seal before painting
PVC pipe Frames and structure Check the fit before you glue
Worbla Shaped and detailed pieces Softens at about 90°C (194°F)
3D prints (PLA) Fine detail and repeat parts Needs sanding and filler primer
Polymer clay Small details and medallions Must be oven-baked; it doesn’t air dry
Resin and body filler Hard-shell papercraft pieces Ventilate; sand with a dust mask

EVA foam basics

  • Thickness: 2 mm sheet works for details, 5 to 6 mm for armour and 10 mm for thick parts. High-density foam cuts and sands more cleanly than cheap floor-mat foam.
  • Cutting: use a fresh blade and change it often for clean bevels.
  • Sealing: heat-seal the surface with a heat gun before priming, to close the pores.
  • Joins: use contact cement. Coat both surfaces, wait until they are dry to the touch (about 10 to 15 minutes), then press. Contact cement doesn’t bond while wet. Hot glue is not a substitute on seams.
  • Priming: prime with Plasti Dip (about three thin coats), Flexbond or Mod Podge before painting. Acrylic paint straight onto raw foam cracks and soaks in.

Worbla and thermoplastics

Worbla softens at about 90°C (194°F) and sticks to itself when hot. Shape it with care, since heat guns can exceed 500°C (930°F). Don’t touch the nozzle, and work in a ventilated space.

Shape with patterns

Pepakura unfolds a 3D model into paper templates. You can use those templates to cut card or foam parts that fold into a larger shape.

3D prints and hard shells

  • PLA prints: sand through 120, 220 and 400 grit. Apply filler primer, then repeat until the surface is smooth.
  • Hard-shell papercraft: coat the inside with resin, then build up the outside with body filler and sand it.

Repeat details with silicone molds

Silicone molds let you cast repeated details such as rivets, gears and gems. Cast them in a consistent material, and check each one before you attach it.

Paint and finish

Work through a base coat, a metallic layer, dry-brushed highlights, a dark wash and a clear coat. For steampunk finishes, see how do you make steampunk.

Conventions and realistic props

Many conventions require props to be checked, peace-bonded, or barred if they look realistic. Keep realistic prop weapons out of public view, and check each event’s rules before you go. For a blaster-based prop, see steampunk Nerf gun mods.

Safety

  • Ventilate when using contact cement and resin. Wear an organic-vapour respirator indoors.
  • Wear a dust mask (N95 or better) when sanding fillers and 3D prints.
  • Keep hands away from the heat gun nozzle.

For a wider look at what materials suit steampunk builds, see what materials are used in steampunk. For more projects, see the steampunk DIY crafts guide.

The complete guide to diy crafts

Steampunk DIY Crafts: Projects, Props and Gifts to Make
Read the guide

Keep exploring

Guides from other topics

All topics →