DIY Crafts

How to make a homemade gearbox?

Build a homemade gearbox for a steampunk display: work out gear ratios, match tooth sizes so gears mesh, pick materials, and leave clearance for smooth turning.

On this page
  1. How gear ratios work
  2. Match the teeth
  3. Choose materials
  4. Build steps
  5. Bearings and motors
  6. Clearance and lubrication
  7. Common mistakes
  8. Safety

To make a homemade gearbox, mount gears on shafts inside a rigid frame, choose tooth counts that give the speed or torque you want, and keep the teeth matched so they mesh. Cardboard, plywood, 3D-printed PLA and LEGO Technic gears all work for prototypes and display builds.

In a steampunk piece, a visible gearbox can drive a clock hand, a crank or a moving display wheel. The ratio sets how fast that part turns, so it is worth working out before you build the frame.

How gear ratios work

  • Ratio: driven gear teeth ÷ driving gear teeth. A 40-tooth gear driven by a 10-tooth gear gives 4:1.
  • Speed and torque: output speed is input speed ÷ ratio. Output torque is roughly input torque × ratio, minus friction losses.
  • Power: gears don’t create power. Trading speed for torque loses some energy to friction.
  • Compound trains: stage ratios multiply. Two stages of 3:1 and 4:1 give 12:1.
  • Idlers: an idler gear reverses direction but doesn’t change the overall ratio.
  • Direction: each mesh between two external gears reverses rotation.
  • Worm gears: these give high reduction and are often self-locking. Their ratio is wheel teeth ÷ worm starts.

Match the teeth

Gears that mesh must share the same module (metric) or diametral pitch (imperial), and the same pressure angle. A 20° pressure angle is standard, and 14.5° is found on older gears.

  • Module = pitch diameter (mm) ÷ number of teeth.
  • Centre distance = (pitch diameter 1 + pitch diameter 2) ÷ 2.
  • Gear diameter alone doesn’t set the ratio. Tooth count does.
  • Decorative gears of a different module won’t mesh, even when they look close.

Choose materials

  • Plywood or MDF, cut on a scroll saw or laser cutter.
  • 3D-printed PLA or PETG.
  • LEGO Technic gears, which come in 8, 12, 16, 20, 24, 36 and 40 teeth.
  • Cardboard or foam-core prototypes. A prototype lets you place the gears before you cut the final frame.

For printable gear templates, online generators such as Matthias Wandel’s woodgears.ca are a common choice. For card-based gears, see steampunk gears and cogs.

Build steps

  1. Choose the ratio you need, then pick the tooth counts that give it.
  2. Build the housing: cut a rigid frame with aligned holes or bearings for the shafts.
  3. Mount the shafts and gears. Space them so the teeth mesh without binding or slipping.
  4. Turn the input shaft by hand to check alignment, then lubricate.

Prototype on cardboard first. Mark the shaft positions on paper, then transfer them to the final frame.

Bearings and motors

  • Bearings: 608 skateboard bearings (8 mm bore, 22 mm outer diameter, 7 mm wide) are cheap and common for shafts.
  • Motors: yellow “TT” hobby gear motors are typically about 1:48.

Clearance and lubrication

Allow a small amount of backlash, which is the slack between meshing teeth. Zero clearance makes gears bind. Use dry PTFE or plastic-safe grease on plastic gears, and wax on wood gears.

Common mistakes

  • Gears of different module or pitch won’t mesh properly, even if the sizes look close.
  • An idler gear doesn’t add reduction.
  • Gears don’t add power, so a gearbox can’t make a weak motor stronger.

Safety

  • Gear meshes are pinch points. Guard any powered gearbox.
  • Wear eye protection when cutting gears on a scroll saw or laser.
  • If you plan to use a metal shop, take training on the machines first. Metalworking tools can cause serious injuries.

For the wider range of steampunk builds, see the steampunk DIY crafts guide.

The complete guide to diy crafts

Steampunk DIY Crafts: Projects, Props and Gifts to Make
Read the guide

Keep exploring

Guides from other topics

All topics →