DIY Crafts

How to Make a Steampunk USB Flash Drive

Turn a cheap USB flash drive into a steampunk gift: remove the shell, insulate the circuit board, fix it in a brass or wood housing and finish it.

On this page
  1. What you need
  2. Check the donor drive first
  3. Remove the shell safely
  4. Insulate before you house it
  5. Fix the board in the housing
  6. Keep the plug straight and exposed
  7. Add details and finish
  8. Optional: show the LED
  9. Add a loop
  10. Common mistakes
  11. Safety

A steampunk USB flash drive is a small, practical gift: a cheap drive with its plastic shell swapped for a brass, wood or putty housing. The main job is keeping the electronics safe and the plug usable in a port.

What you need

  • A cheap USB flash drive to use as the donor.
  • A housing, such as brass plumbing fittings, wood blocks, spark plugs, old pocket-watch cases, keys or pipe nipples.
  • Heat-shrink tubing or Kapton tape to insulate the circuit board.
  • Two-part epoxy or epoxy putty, such as Milliput or Apoxie Sculpt.
  • E6000 or epoxy for decorative parts, plus Rub ’n Buff or metallic paint and a dark wash.
  • A jump ring or split ring for a keychain loop.

Check the donor drive first

Capacity, speed and reliability depend on the donor drive, not the case. Test the drive on a computer before you remove the shell, then test it again before the final gluing.

A USB-A plug is about 12 mm wide and 4.5 mm tall, so the housing opening must clear it. USB 3.0 plugs have extra contacts, usually visible as a blue tongue. Either type works if the plug is left exposed.

Remove the shell safely

Score the shell, then pry it off with the blade moving away from your hand. Wear eye protection when you cut metal. Ground yourself before you touch the bare circuit board, since static can damage it.

Insulate before you house it

Insulate the board with heat-shrink tubing or Kapton tape before it goes into any metal housing. A bare board in a metal case can short out. Metal doesn’t protect the board unless it’s insulated first.

Fix the board in the housing

Bond the board with two-part epoxy or epoxy putty. Working times vary by brand, often around 1 to 3 hours, and full cure is commonly about 24 hours. Keep glue off the plug contacts.

Hot glue alone won’t hold the plug. Repeated insertion can twist a hot-glued plug loose.

Keep the plug straight and exposed

The full metal plug should be exposed and straight, so it seats fully in the port. Keep the total width small enough that it won’t block neighbouring ports. About 15 to 18 mm is a comfortable target, though laptops vary.

Add details and finish

Add gears, rivets or watch parts with E6000 or epoxy, and let them cure for 24 to 72 hours before use. Finish metal or putty with Rub ’n Buff or metallic paint, then add a dark wash. For ideas on materials, see what materials are used in steampunk.

Optional: show the LED

Most drives have a small LED on the board. If you want it visible, drill a small window in the housing over it.

Add a loop

Fit a jump ring or split ring so the drive can hang from a keychain.

Common mistakes

  • Hot glue won’t hold the plug in place for long.
  • The housing doesn’t change capacity or speed.
  • Glue must stay off the contacts, or the drive may not connect.

Safety

  • Score and pry the shell with the blade away from your hand.
  • Wear eye protection when you cut metal.
  • Ground yourself before touching the bare board.

Test the finished drive on a computer before you give it away. For a larger project that uses gears, see steampunk gears and cogs, or browse the steampunk DIY crafts guide.

The complete guide to diy crafts

Steampunk DIY Crafts: Projects, Props and Gifts to Make
Read the guide

Keep exploring

Guides from other topics

All topics →