DIY Crafts

DIY Steampunk Industrial Pipe Lamp and the Parts You Need

Parts list for a steampunk industrial pipe lamp: pipe sizes and fittings, a lamp socket and cord, wiring safety, and a note on oil-lamp burners.

On this page
  1. Parts list
  2. Understand pipe sizes
  3. Bulbs and sockets
  4. Prepare the pipe
  5. Wiring basics
  6. Build and finish
  7. Oil-lamp version
  8. Safety

An industrial pipe lamp uses old-style pipe as its body, with a large bulb and often a gauge or clock face for effect. This guide covers the parts for an electric version, then a short section on an oil-lamp version. For either one, the two things to get right are the pipe sizes and the wiring.

Parts list

For the electric version, you’ll need:

  • A floor flange for the base
  • Nipples, elbows, tees and caps to build the shape
  • A lamp socket (E26 in the US, E27 in Europe)
  • A 1/2-inch NPT-to-1/8 IPS reducer, to mount a standard lamp socket on the pipe
  • 18-gauge two-wire lamp cord (SPT-1 or SPT-2) with a polarized plug
  • An optional switch

A UL-listed lamp kit, or the local equivalent, is the simplest compliant option. Decorative valves don’t switch the lamp unless a switch is wired in.

Understand pipe sizes

A “1/2-inch” pipe is not 1/2 inch across. That name is a nominal size, and the outside diameter is about 0.84 inch (21 mm).

Pipe uses tapered NPT threads, while standard lamp parts use 1/8 IPS threads on a rod about 3/8 inch across. That’s why lamp sockets don’t thread straight onto plumbing pipe, and why you need a reducer.

Bulbs and sockets

US sockets are E26 and European sockets are E27. Vintage bulb shapes include ST64, A19 and G40. LED filament Edison-style bulbs typically draw about 4 to 8 W, compared with 40 to 60 W for incandescent bulbs, and they run much cooler.

Prepare the pipe

  • Degrease: black pipe ships oily. Clean it with mineral spirits or dish soap, then seal it with lacquer or wax.
  • Deburr: smooth the pipe ends so they don’t cut the cord insulation.
  • Drill and sand: drill a hole large enough for the cord, and sand its edges smooth.
  • Skip the tape: plumbing tape isn’t needed on a lamp, because the joints aren’t under pressure.

Wiring basics

This section is an overview, not a full wiring guide. If you aren’t confident working with mains wiring, use a ready-made lamp kit or ask a qualified electrician to check the work.

  • Unplug the cord before you wire anything.
  • Feed the cord through the pipe before you assemble the parts.
  • On a polarized lamp cord, connect the ribbed (neutral) conductor to the silver screw and the smooth (hot) conductor to the brass screw.
  • Tie an Underwriter’s knot inside the socket for strain relief.
  • Keep the cord insulation intact wherever it touches metal.

Build and finish

Arrange the pipe pieces before you join them, and check the fit with the socket in place. When the shape works, spray the pipe in thin coats, let the paint cure fully and seal it. For paint techniques, see how do you make steampunk.

Oil-lamp version

An oil lamp uses a flat-wick burner. Common sizes are No. 0 (5/8 inch), No. 1 (7/8 inch), No. 2 (1 inch) and No. 3 (1.5 inches). Burn only paraffin lamp oil or K-1 kerosene.

Never put gasoline, white gas or alcohol in an oil lamp. Citronella and tiki-torch fuel are for outdoor use only.

Safety

  • Unplug the lamp before wiring or adjusting it.
  • Keep the cord insulation intact wherever it touches metal.
  • Let incandescent bulbs cool before you handle them.
  • Use only the fuels listed for oil lamps, and keep them away from the flame when refilling.

For the wider range of steampunk décor, see the steampunk DIY crafts guide.

The complete guide to diy crafts

Steampunk DIY Crafts: Projects, Props and Gifts to Make
Read the guide

Keep exploring

Guides from other topics

All topics →